Home > Products > Tapered Roller Bearing > Needle Bearing > Needle roller bearing ZGN357036

Needle roller bearing ZGN357036

Basic Info

Model No.ZGN357036

BrandAUTO

Rolling BodyRoller Bearings

The Number of RowsSingle

Outer DimensionMedium and Large(120-190mm)

MaterialBearing Steel

SphericalAligning Bearings

Load DirectionRadial Bearing

SeparatedUnseparated

Additional Info

Productivity5000ps/month

TransportationOcean,Land,Air

Place of OriginChina

Supply Ability5000ps/month

CertificateISO9001

HS Code8482200000

PortShanghai,Qingdao,Other Chinese Ports

Payment TypeL/C,T/T,Paypal

IncotermFOB,CFR,CIF,FCA,CPT

Product Description

Install full Needle Roller bearings, usually with an auxiliary sleeve. At this time, the auxiliary roller or the auxiliary sleeve holds the needle to keep the needle from falling out, and the journal lifts the needle up with its own chamfering Angle. As the Needle Roller Bearing moves slowly in the journal, the auxiliary roller or the auxiliary sleeve will slowly exit until it is installed to the working position. The outer diameter of the auxiliary roller and the auxiliary sleeve should be 0.1-0.3mm smaller than the diameter of the shaft. When installation, the surface coated with grease inside the bearing outer ring first, against the tight inner surface needle needle: (in the last one should be gaps), then replace the shaft neck of the Roller Bearing inner ring or auxiliary sleeve into the outer ring hole, and make it face alignment installed shaft end face or installed on the shaft bearing inner ring end face, and then use pressure on the press or hammer knock. The needle roller bearing can also be installed in this way. A thin layer of lubricant is applied to the outer diameter of the auxiliary sleeve, and the outer ring of the bearing is inserted into it so that the auxiliary sleeve and the outer ring of the bearing constitute an annular hole, and then the needle is installed in the annular hole. After mounting the needle roller, the auxiliary sleeve can be pushed out with the working shaft. For needle roller bearings without inner ring or outer ring, a thin layer of grease can be applied to the rolling surface of the shaft or housing hole, and the needle can be pressed against the grease of the mounting part in turn. The gap should be left when the last needle is attached. The size of the gap should be 0.5mm on the circumference of the Needle Bearing. The last roller can not be squeezed into, or less than one needle, because the bearing will be stuck and cannot rotate when the hard squeeze is installed; When less mounting, the gap is too large, easy to cause the rolling pin to twist and break when the bearing is running. For the needle roller bearing which only has the stamping outer ring, since the outer ring wall is very thin, the needle roller bearing should be installed with a hand hammer, and should be pressed by the press machine. Because the pressure is not uniform when the hammer strikes, it is easy to cause local deformation of the outer ring of the needle roller bearing.


Zgn357036


Bearing code:Needle roller bearing ZGN357036

d=35

D=70

B=23


Brand: AUTO
Series: deep groove ball bearings, single row, Tapered Roller Bearing ,Cross Cylindrical Roller Bearing,Angular Contact Ball Bearing,Needle roller bearing
Luoyang Auto Bearing Co., Ltd. is located in the ancient capital of four China - Jianxi Industrial Park in Luoyang, is a member of China bearing industry alliance, in close cooperation with the national Chinese bearing level testing center, is a professional R & D, manufacturing, production and sales of high quality bearing products enterprises.
The company mainly produces deep groove ball bearings, aligning ball bearings, turntable bearings, cross roller bearings and other kinds of high-precision bearing products, mainly used in motor industry, mining and metallurgy, wind power generation, oil drilling, automobile and motorcycle and other fields.
The company has the international advanced level professional test instrument, each process strictly controls the quality according to the ISO9001Z quality management system request, effectively guarantees the product accuracy and the performance stability. The AUTO bearings produced by our company are mainly exported to the United States, Korea, Europe and other markets, and have reached the quality level of the international similar products.
"Details, quality and quality" is our company's cultural core. We adhere to the production and management concept of "boutique bearing and quality assurance", adhere to zero defect quality control, and provide customers with satisfactory products.

Product Categories : Tapered Roller Bearing > Needle Bearing

Product Images

  • Needle roller bearing ZGN357036
Email to this supplier
  • Mr. Moore Liu
  • Your message must be between 20-8000 characters

Related Productslist

Home

Phone

Skype

Inquiry